Recent Posts

Pages: [1] 2 3 ... 10
1
Vehicle Electrics / Re: Spark plug torque specification (2008)
« Last post by Mugglescience on October 21, 2018, 07:44:24 PM »
Cheers :)
2
Vehicle Electrics / Re: Spark plug torque specification (2008)
« Last post by cosh68 on October 21, 2018, 05:24:08 PM »
Dan,

They will be fine....

Shaun....
3
Vehicle Electrics / Re: Spark plug torque specification (2008)
« Last post by Mugglescience on October 20, 2018, 10:11:20 PM »
I did them to 12nm (snug plus 1/2 a turn as that was advised on the ngk box. Think they?ll be fine or should I tighten a bit more?
4
Vehicle Electrics / Re: Spark plug torque specification (2008)
« Last post by cosh68 on October 20, 2018, 08:39:46 PM »
Mugglescience,

15 - 22 Nm

https://ibb.co/n7z4wL

Shaun....
5
Engine/Transmission/Powertrain/Exhaust / Re: OBDII Error P0328 - Anyone else??
« Last post by DarkKnight on October 20, 2018, 02:48:34 PM »
Hi Cosh,

Thanks for the prompt reply,
Great help.
This is the part I need?  https://www.ebay.co.uk/itm/Genuine-Mazda-2-2007-2014-Petrol-Engine-Knock-Sensor-ZJ0118921-/282112594940
Lifting the bonnet up, the knock sensor seems to be plugged in correctly, so I assume its a malfunction.

Again many thanks for the help,
Rob.


6
Troubleshooting / Re: Squeaky Mazda 2
« Last post by Mugglescience on October 20, 2018, 01:22:11 PM »
I took a look at the ECP gasket and it was a bit thinner than the one i got from the mazda dealer, so that's your best bet!
7
Troubleshooting / Re: Squeaky Mazda 2
« Last post by scottb88 on October 20, 2018, 01:08:42 PM »
Hi, thanks for the replies.

Its reassuring to hear you had the same issue, your spot on though it was an aftermarket gasket from euro car parts. I did clean it up but with a wire brush and some rag.

I'll try it again but with one from the mazda dealership.

 Cheers
8
Troubleshooting / Re: Squeaky Mazda 2
« Last post by Mugglescience on October 20, 2018, 09:48:11 AM »
Just watched the video. That is 100% the donut gasket still. You must have used aftermarket or did the job wrong. Did you clean the flange with some fine grit sandpaper before putting it back together?
9
Troubleshooting / Re: Squeaky Mazda 2
« Last post by Mugglescience on October 20, 2018, 09:45:39 AM »
Mine did exactly this and i suffered it for 15k miles until i finally got round to changing that donut gasket.

Did you use the OEM one from a mazda garage or aftermarket?

I'd spray some silicone lubricant into the mounts and also suspension bushings and see if it still does it. If it does, you can be sure it's one of those. Also check pulleys and the belt tensioner, as this can also be a source of squeaking when changing gear. Wouldn't recommend changing the tensioner unless you really believe its failing though as it's ?140!
10
Vehicle Electrics / Spark plug torque specification (2008)
« Last post by Mugglescience on October 20, 2018, 09:25:51 AM »
Hi All,

Looking for the spark plug torque specification for the 2008 model.

Thanks!
Pages: [1] 2 3 ... 10